Embellish® Sticky Tearaway is a pressure sensitive, needle-friendly, light tearaway stabilizer made using the “Non-Woven” technique. Our unique base material is constructed with a combination of 50% soft tearaway fibers and 50% water-soluble fibers, making it very easy to remove from delicate embroidery or embellishments. Use this premium sticky stabilizer when working with items that are distinguished as “hard to hoop” or fabrics that could be harmed/marked by the hooping process such as: collars, cuffs, socks, corners, burlap, cardstock, corduroy, cork fabric, cuddle, jeggings, leather, low-pile fur, oilcloth, towels, watercolor paper and velvet. This is the ideal “vehicle” for getting smaller items under the needle for embellishment such as: baby onesies, pockets, T-Shirts, etc. Use our non-sticky version, Embellish® Dissolvable Tearaway, when additional design support is needed by floating a piece under the embroidery hoop. This is necessary when the design stitch count is more than 10,000 stitches in a 4”x 4” hoop.

Contents:

Made in America. Constructed of 50% soft tearaway fibers and 50% soft, water-soluble fibers with a light, pressure-sensitive, needle-friendly, water-soluble coating. 1.8 oz.

Stitch Count

Holds up to 10,000 embroidery stitches in a 4″ x 4″ hoop.

To Use:

1. Hoop one piece of Embellish® Sticky Tearaway with the release paper (shiny side) facing up. Make sure the stabilizer is “tight as a drum” in the hoop.
2. Draw an “X” on the surface with the Embellish® Vinyl Weeding Tool, taking care not to puncture the stabilizer. This will perforate the paper so it can easily be torn away, exposing the sticky surface.
3. Finger-press the wrong side of the item to the sticky surface and smooth out the wrinkles. 4. If the design has more than 10,000 stitches in a 4” x 4” hoop, “float” a piece of Embellish® Dissolvable Tearaway under the hoop for added support.
4. Add an embroidery topper on top of the hooped item (either Embellish® Rinse-Away Clear Topper or Embellish® Iron-Away Clear Topper).
5. Embroider the design. If your machine has an auto-baste function, it is recommended to baste the design and topper before embroidering.

To Remove:

1. Remove the material from the hoop.
2. Hold your fingers over the bobbin thread and tear away as much of the stabilizer as possible, starting with the “floater.”
3. Optional Method – Wet around the edge of the design using a Q-Tip, sponge, foam paint brush or envelope sealer. Wait about 5 seconds to allow the water to activate the water-soluble portion of the stabilizer. Or, lay a damp cloth on the back side until fibers start to dissolve. This method is perfect for a project that you are not going to launder.

Laundering and Care:

Launder and dry the item according to the fabric material fiber content. Stabilizer remnants will continue to wash out in the laundry with a mild detergent and agitation.

The post Sticky Tearaway appeared first on RNK Distributing.

Embellish® Fusible Dissolvable Tearaway is a temporary fusible, light tearaway stabilizer made using a unique “Non-Woven” technique. It is made with a combination of 50% soft tearaway fibers and 50% water-soluble fibers, making it very easy to remove from delicate embroidery, satin or decorative stitching. Use with light to medium, open airy embroidery designs on fabrics such as: cotton, linen, batiste, kitchen flour sack towels, rayon, and silk. Use the non-fusible version, Embellish® Dissolvable Tearaway, as additional support, if needed, by floating a piece under the embroidery hoop when the design stitch count is more than 10,000 stitches in a 4”x 4” hoop. Because of the unique 50/50 fiber combination, this stabilizer leaves a very soft-hand when laundered, because half of the fibers wash-away.

These embroidered jeans were made with the Roses & Arrows Embroidery & SVG Collection & the Embellish Rinse Away Clear Topper

Contents:

Made in America. Constructed of 50% soft tearaway fibers and 50% water-soluble fibers with a light temporary, fusible coating. 1.8 oz.

Stitch Count:

Holds up to 10,000 embroidery stitches in a 4”x4” hoop.

To Use:

1. Fuse one layer of the stabilizer to the back of the material. Be sure to use a piece at least one inch larger than the outer perimeter of the hoop to ensure proper stabilization. * Important – Use a low temp (Silk Setting) on your iron. Do NOT touch the surface of your iron to Embellish® Fusible Dissolvable Tearaway, press from the fabric side or use a press cloth (natural fibers such as muslin or cotton). All irons heat differently. The iron temperature given is a starting point. If you find that you are not getting a good fuse, slowly increase your iron’s temperature, until you achieve a good bond, between the fabric and stabilizer and ensure the stabilizer can be torn away easily. If it won’t release easily when torn away, the iron temperature is too high.
2. Hoop the material along with the fused stabilizer, making sure the material and stabilizer are taut.
3. If the design has more than 10,000 stitches in a 4”x 4” hoop, “float” a piece of non-fusible Embellish® Dissolvable Tearaway under the hoop for added support.
4. Add an embroidery topper on top of the hooped item (either Embellish® Rinse-Away Clear Topper or Embellish® Iron-Away Clear Topper).
5. Embroider the design.

To Remove:

1. Remove the material from the hoop. Remove the topper, following the topper product sheet, found in this workbook.
2. Hold your fingers over the bobbin thread and tear away as much of the stabilizer as possible, starting with the “floater.”
3. If the iron temperature was too hot during the fusing process of the Embellish® Fusible Dissolvable Tearaway, it might be necessary to re-heat the stabilizer, using a Silk Setting, for it to release from the material.
4. *Optional Method for Delicate Embroidery or Stitching – Wet around the edge of the design using a Q-Tip, sponge, foam paint brush or envelope sealer. Wait about 5 seconds to allow the water to activate the water-soluble portion of the stabilizer. Or, lay a damp cloth on the back side, until fibers start to dissolve. This method is perfect for a project that you are not going to launder.

Laundering and Care:

Launder and dry the item according to the fabric material fiber content. Stabilizer remnants will continue to wash out in the laundry with a mild detergent and agitation.

The post Fusible Dissolvable Tearaway appeared first on RNK Distributing.

Embellish® Fusible Bold Tearaway is a tightly woven, heavy duty, fusible stabilizer made using a unique “Non-Woven” technique. The fusible coating is temporary, so it pulls away easily when ironed at the proper temperature. It is used to support decorative sewing stitches and large or dense embroideries on stable woven fabric such as: cotton, duck cloth, twill, and denim. It features a multi-directional tear capability, easily pulling away clean from the embroidery design, for a crisp look on the front and back. Also available in a non-fusible version, which is to be used as additional support by floating a piece under the embroidery hoop when the design stitch count is more than one layer of Embellish® Fusible Bold Tearaway can sustain.

Contents:

Made in America. Premium tearaway fibers using the Wet-Laid Non-Woven Process with a light temporary fusible coating. 2 oz.

Stitch Count:

Holds up to 12,000 embroidery stitches in a 4”x4” hoop.

To Use:

1. Fuse one layer of the stabilizer to the back of the material. Be sure to use a piece at least one inch larger than the outer perimeter of the hoop to ensure proper stabilization.Important – Use a low temp (Silk Setting) on your iron. Do NOT touch the surface of your iron to Embellish® Fusible Bold Tearaway, press from the fabric side or use a press cloth (natural fibers such as muslin or cotton). All irons heat differently. The iron temperature given is a starting point. If you find that you are not getting a good fuse, slowly increase your iron’s temperature until you achieve a good bond between the fabric and stabilizer and ensure the stabilizer can be torn away easily. If it won’t release easily when torn away, the iron temperature is too high.
2. Hoop the material along with the fused stabilizer, making sure the material and stabilizer are taut.
3. If the design has more than 12,000 stitches in a 4”x4” hoop then “float” a piece of non-fusible Embellish® Bold Tearaway under the hoop for added support.
4. Add an embroidery topper on top of the hoop (either Embellish® Rinse-Away Clear Topper or Embellish® Iron-Away Clear Topper).
5. Embroider the design.

To Remove:

1. Remove the material from the hoop. Remove the topper, following the topper product sheet.
2. Hold your fingers over the bobbin thread and tear away as much of the stabilizer as possible, starting with the “floater,” if applicable.
3. If the iron temperature was too hot during the fusing process, it might be necessary to re-heat the stabilizer, using a Silk Setting for it to release from the material.

Laundering and Care:

Launder and dry the item according to the fabric material fiber content.

The post Fusible Bold Tearaway appeared first on RNK Distributing.

Light Tearaway Stabilizer featuring Water Soluble Fibers

Embellish® Dissolvable Tearaway is a light tearaway stabilizer made using a unique “Non-Woven” technique. It is made with a combination of 50% soft tearaway fibers and 50% water-soluble fibers, making it very easy to remove from embroidery and machine decorative stitches. For embroidery, use with light to medium, open airy designs on fabrics such as: cotton, linen, batiste, kitchen flour sack towels, rayon, and silk. It is also available in a fusible and sticky version. Embellish® Dissolvable Tearaway is recommended to be used as a “floater” under the hoop, when used in conjunction with Embellish® Fusible Dissolvable Tearaway, that has been ironed to the back of the woven fabric. If the material cannot be ironed or is too small to be hooped, then we recommend using Embellish® Sticky Tearaway as it’s made from the same 50/50 base.

Using Embellish® Dissolvable Tearaway as a “floater” adds additional support to the design and fabric, when using a design that has more than 10,000 stitches in a 4”x 4” hoop. When laundered, the water soluble fibers dissolve leaving behind a very soft embroidery.

Contents:

Made in America. Constructed of 50% soft tearaway fibers and 50% water-soluble fibers. 1.8 oz.

Stitch Count:

Holds up to 10,000 embroidery stitches in a 4”x4” hoop.

To Use:

1. Cut a “floater” piece at least one inch larger than the outer perimeter of the embroidery design to ensure proper stabilization.
2. Hoop the material along with the fused Embellish® Fusible Dissolvable Tearaway, making sure the material and stabilizer are taut.
3. If the design has more than 10,000 stitches in a 4”x 4” hoop, “float” a piece of non-fusible Embellish® Dissolvable Tearaway under the hoop for added support.
4. Add an embroidery topper on top of the hoop (either Embellish® Rinse-Away Clear Topper or Embellish® Iron-Away Clear Topper).
5. Embroider the design.

To Remove:

1. Remove the material from the hoop. Remove the topper, following the topper product sheet.
2. Hold your fingers over the bobbin thread and tear away as much of the stabilizer as possible, starting with the “floater.”
3. If the iron temperature was too hot during the fusing process of the Embellish® Fusible Dissolvable Tearaway, it might be necessary to re-heat the stabilizer, using a Silk Setting for it to release from the material.
4. *Optional Method for Delicate Embroidery or Stitching – Wet around the edge of the design using a Q-Tip, sponge, foam paint brush or envelope sealer. Wait about 5 seconds to allow the water to activate the water-soluble portion of the stabilizer. Or, lay a damp cloth on the back side until fibers start to dissolve. This method is perfect for a project that you are not going to launder.

Laundering and Care:

Launder and dry the item according to the fabric material fiber content. Stabilizer remnants will continue to wash out in the laundry with a mild detergent and agitation.

The post Dissolvable Tearaway appeared first on RNK Distributing.

Embellish® Bold Tearaway is a tightly woven, heavy duty, stabilizer made using a unique “Non-Woven” technique, and it is used to support large or dense embroideries on stable woven fabric such as: cotton, duck cloth, twill, and denim. It features a multi-directional tear capability, easily pulling away clean from the embroidery design for a crisp look on the front and back. It is also available in a fusible version. Embellish® Bold Tearaway is recommended to be used as a “floater” under the hoop when used in conjunction with Embellish® Fusible Bold Tearaway that has been ironed to the back of woven fabric. Adding a “floater” of Embellish® Bold Tearaway adds additional support to the fabric when using a design that has more than 12,000 stitches in a 4”x4” hoop.

Contents:

Made in America. Premium tearaway fibers using the Wet-Laid Non-Woven Process. 2 oz.

Stitch Count

Holds up to 12,000 embroidery stitches in a 4”x4”

To Use:

1. Cut a “floater” piece at least one inch larger than the outer perimeter of the embroidery design to ensure proper stabilization.
2. Hoop the material along with the fused Embellish® Fusible Bold Tearaway, making sure the material and stabilizer are taut.
3. If the design has more than 12,000 stitches in a 4” x 4” hoop then “float” a piece of non-fusible Embellish® Bold Tearaway under the hoop for added support.
4. Add an embroidery topper on top of the hooped material (either Embellish® Rinse-Away Clear Topper or Embellish® Iron-Away Clear Topper).
5. Embroider the design.

To Remove:

Remove the material from the hoop. Remove the topper following the topper product sheet found in this workbook.
Hold your fingers over the bobbin thread and tear away as much of the stabilizer as possible, starting with the “floater.”
If the iron temperature was too hot during the fusing process of the Embellish® Fusible Bold Tearaway, it might be necessary to re-heat the stabilizer using a Silk Setting for it to release from the material.

Laundering and Care:

Launder and dry the item according to the fabric material fiber content.

The post Bold Tearaway appeared first on RNK Distributing.